clearance fit
英 [ˈklɪərəns fɪt]
美 [ˈklɪrəns fɪt]
间隙（动座；活动）配合
双语例句
- The vent system composed of vent groove, vent plug and clearance of ejector pin can fit the need of venting.
采用分型面排气槽、顶杆间隙排气与排气塞排气相结合的排气系统设计能够很好地满足模具排气需要。 - The programming button ( 1) is positioned in the button hole ( 2), and is in clearance fit with the button hole ( 2);
所述编程按钮（1）位于按钮孔（2）中，并与按钮孔（2）间隙配合； - Can counterclockwise unscrewing the grip the lock nut and adjust control again, until the nut spin twist clearance fit.
可以逆时针拧松握把根部的锁紧螺母，再左右旋拧调整螺母，直到间隙合适为止。 - Also it has, with the method of 3D FEA, through use clearance fit in the higher load hole and interference fit in the lower load hole to proportion load distribution.
采用三维有限元法，利用在大载荷孔上使用间隙配合、在小载荷孔上施加干涉配合的方法，使各钉载荷分配均匀化。 - The laws of Change in Material Strength of Structural Parts and Change in Clearance of Shrink Fit of The Shaft-through for The Explosion-proof Motor used in Low Temperature Ambience
低温防爆电动机结构件材质强度及轴贯通配合间隙冷缩变规律 - The relation between the outer diameter of free upsetting blank and the inner diameter of cold extrusion die can be comprehended as clearance fit, to confirm the basic tolerance and tolerance band of the blank.
将自由镦粗毛坯外径与冷挤压凹模的关系理解为间隙配合，确定了毛坯的基本偏差和公差带。 - Among refrigerant leakages are caused by clearance fit in rolling piston compressors, the maximal amount of leakage is occurred in the radial clearance, which is mainly processed by the mode that the refrigerant dissolves into the lubricant.
在滚动转子式压缩机内由于间隙配合造成的制冷剂泄漏中，转子径向间隙的泄漏量最大，它主要是以溶于润滑油的形式泄漏的。 - This chapter introduces a way by which interference fit or clearance fit probability needed in transition fit can be exactly designed, when selecting transition fit and applying probability statistic theory.
介绍设计过程中选用过渡配合时，应用概率统计理论，精确设计过渡配合中需要出现过盈、间隙配合概率的方法。 - With the analysis of clearance fit between piston and cylinder lin-er and the measurement of static deformation of engine block and cylinder liner, an improvement was proposed to strengthen the rigidity of 490 engine block in or-der to eliminate the early scuffing of cylinder bore.
本文针对490型柴油机出现的早期拉缸现象，通过对活塞与气缸套配合间隙的分析试验及对机体、缸套静变形的测量分析，着重提出了加强机体刚度的改进措施。 - In rolling piston compressors, clearance fit is adopted between rotor and cylinder. Its leakage passages are pressurized by oil films.
在转子压缩机内转子和气缸之间采用间隙配合，其泄漏通道通过油膜来密封的。 - The influence of thermal deformation on clearance fit and interference fit are discussed. A new tolerance design method that compensates thermal deformation is presented.
本文重点分析热变形对孔、轴类配合的影响，提出了通过修正公差设计补偿热变形误差的理论方法和具体措施，为全面提出热公差配合理论奠定了良好的基础； - It was found by calculation that thrust load has an evident effect on contact angle while radial load influence feebly, clearance has a great impact on load distribution and appropriate interference fit increases carrying capacity, but the maximum needle burthen also increases.
计算结果表明，角接触球轴承的轴向载荷对工作接触角影响明显，而径向载荷影响很小；游隙对滚针轴承载荷分布的影响很大，适当过盈可提高承载力，但滚针最大负荷增大。